The patented cable tray system is designed to be stronger, optimally stack able and transportable, quick to install, with random overlap and exceedingly safe.
150mm X 50mm Nigeria made Galvanized Cable Tray By 2.5 Meter
Embedded perforations for : – extra load capacity – better aeration – better stability – better condensation drainage Alternative perforations for : – better fixation on the supports – very useful for cable fixation -Standard finish Galvanized
₦4,100.00
CompareBased on 0 reviews
Be the first to review “150mm X 50mm Nigeria made Galvanized Cable Tray By 2.5 Meter”
-
DISTRIBUTION BOARDS, DISTRIBUTION BOARDS, Electro
Schneider Electric 3 Phase 12 Ways Distribution Board FLUSH Disbo Extra
DISTRIBUTION BOARDS, DISTRIBUTION BOARDS, ElectroSchneider Electric 3 Phase 12 Ways Distribution Board FLUSH Disbo Extra
Key Features
Full range of device accessories and auxiliaries
Knockouts for cable gland and conduit mixed to suit the installation needs without loss of space
Removable insulated pan assembly
Fully shrouded neutral
Split neutral bars
Removable gland plates
Optional metering, dual supply, surge protection and contactor on incoming Metered extension enclosures.
Product Range – Disbo
Product or Component Type – Distribution Board
Number of Phases – 3 Phase
Number of Ways – 12 Way
Type of Inomer – 3P Isolator 125A
Device Mounting – FlushSKU: Schnieder Disbo -
DISTRIBUTION BOARDS, DISTRIBUTION BOARDS, Electro
Powertec 6 Way 100A Three Phase(TPN) Distribution Board C/W MCB
DISTRIBUTION BOARDS, DISTRIBUTION BOARDS, ElectroPowertec 6 Way 100A Three Phase(TPN) Distribution Board C/W MCB
Features
Compact DBs which occupy minimum space
Raised neutral link for easy wiring
Suitable for surface & fush mounting
Detachable din bar with end stoppers for easy assembly of breakers
Supplied with fully shielded bus-bars
Level marks for providing indication for fitment in wall
Supplied with neutral & earth link, top & bottom detachable plates
Supplied with masking sheet to protect components from cement during plastering.SKU: 281 -
CIRCUIT BREAKERS
TeSys Schneider Electric Overload Relays 7 – 10amps
3-pole relays with screw clamp terminals
These overload relays are designed for the protection of motors. They are
compensated and phase failure sensitive. Resetting can either be manual or
automatic.
Direct mounting: under the contactor for versions with screw clamp terminals only;
pre-wired terminals, see pages B11/28 and B11/30.
Separate mounting: using terminal block LA7 K0064 (see below).
On the front face of the overload relay:
b selection of reset mode: Manual (marked H) or Automatic (marked A),
b red pushbutton: Trip Test function,
b blue pushbutton: Stop and manual Reset,
b yellow trip flag indicator: overload relay tripped.
Protection by magnetic circuit breaker GV2 LE, see pages A6/11 and A6/20.SKU: Overload4 -
ELECTRICAL FITTINGS, Electro, TRUNCKING
75x75mm Dignity PVC Trunking
The advantages of PVC Wire Duct:
1. Low cost, significant cost savings compared to standard traditional tray products.
2. Light in weight, wide range of sizes.
3. Fast heat dispersion.
4. Strong enough to withstand short circuits. Provides strength, rigidity without additional hardware.
5. Adapts to difficult architectural designs to accommodate changes in direction and elevation of cable runs.
6.Flexible, easy and fast installation. Design allows cable exit or entry at any point.
7. Cables can be secured to clamps or ties.
8.Various hardware accessories available to fix, support and install.
9. Safe smooth edge design to protect cable.
10.Easy for line check and cleaning , easy maintained.SKU: 413 -
CHANDELIER LIGHT, Electro, HOME&OFFICE LIGHTING, LIGHTING
Marie Therese Chandelier Clear 5 Arm
‘-For your safety, this product must be installed in accordance with local Building Regulations. If in any doubt, or where required by law, consult a competent person who is registered with an electrical self-certification scheme. Further information is available online or from your local authority.
SKU: 1384 -
ELECTRICAL INDUSTRIAL, Electro, WIRE CABLE TRAY & CABLE LADDER
150mm x 50mm Foreign Wire Merge Cable Tray By 3 Meter
ELECTRICAL INDUSTRIAL, Electro, WIRE CABLE TRAY & CABLE LADDER150mm x 50mm Foreign Wire Merge Cable Tray By 3 Meter
Cable tray are the most common solution for supporting and routing of cables in an installation.
For this reason, cable tray are available in a variety of sizes and standards, in order to cover the
wide range of applications.Embedded perforations for :
– extra load capacity
– better aeration
– better stability
– better condensation drainage
-50x300mmAlternative perforations for :
– better fixation on the supports
– very useful for cable fixation
-Standard finish GalvanizedSKU: LOC150
There are no reviews yet.