Double gang dimmer switch with screw less face plates the ultimate in contemporary switches. This product must be installed in accordance with local Building Regulations. If in any doubt, or where required by the law, consult a competent person who is registered with an electrical self certification scheme. Further information is available online or from your Local Authority. 400W twin dimmer switch. If in doubt consult a qualified electrician.
Twin Dimmer S.Screw Flat 400w
Always read instructions.
₦9,000.00
CompareBased on 0 reviews
Be the first to review “Twin Dimmer S.Screw Flat 400w”
-
SOLAR POWERED
Solar – SZYL-SCL-N803
1. Solar panel: 5W/6V.
2. Lithium battery: 3.7 V/4000 mAh (bottom), 7V/2000mAh (top).
3. Lighting time (top): About 18 hours at low mode, about 10 hours at high mode; Lighting time (bottom): About 30 hours at low mode, About 16 hours at high mode.
4. USB output: 5V/0.5A, 5V/1.5A.
5. Charging time: 5 hours by 5W solar panel.
6. Multi-function: Mosquito Repellent, FM-Radio, MP3-Play, Manual generator device, Mobile charger.SKU: 1532 -
ELECTRICAL FITTINGS, Electro, TRUNCKING
16x25mm Dignity PVC Trunking
The advantages of PVC Wire Duct:
1. Low cost, significant cost savings compared to standard traditional tray products.
2. Light in weight, wide range of sizes.
3. Fast heat dispersion.
4. Strong enough to withstand short circuits. Provides strength, rigidity without additional hardware.
5. Adapts to difficult architectural designs to accommodate changes in direction and elevation of cable runs.
6.Flexible, easy and fast installation. Design allows cable exit or entry at any point.
7. Cables can be secured to clamps or ties.
8.Various hardware accessories available to fix, support and install.
9. Safe smooth edge design to protect cable.
10.Easy for line check and cleaning , easy maintained.SKU: 408 -
CIRCUIT BREAKERS
TeSys Schneider Electric Overload Relays 30 – 40amps
3-pole relays with screw clamp terminals
These overload relays are designed for the protection of motors. They are
compensated and phase failure sensitive. Resetting can either be manual or
automatic.
Direct mounting: under the contactor for versions with screw clamp terminals only;
pre-wired terminals, see pages B11/28 and B11/30.
Separate mounting: using terminal block LA7 K0064 (see below).
On the front face of the overload relay:
b selection of reset mode: Manual (marked H) or Automatic (marked A),
b red pushbutton: Trip Test function,
b blue pushbutton: Stop and manual Reset,
b yellow trip flag indicator: overload relay tripped.
Protection by magnetic circuit breaker GV2 LE, see pages A6/11 and A6/20.SKU: Overload5 -
CIRCUIT BREAKERS
TeSys Schneider Electric Overload Relays 18 – 23amps
3-pole relays with screw clamp terminals
These overload relays are designed for the protection of motors. They are
compensated and phase failure sensitive. Resetting can either be manual or
automatic.
Direct mounting: under the contactor for versions with screw clamp terminals only;
pre-wired terminals, see pages B11/28 and B11/30.
Separate mounting: using terminal block LA7 K0064 (see below).
On the front face of the overload relay:
b selection of reset mode: Manual (marked H) or Automatic (marked A),
b red pushbutton: Trip Test function,
b blue pushbutton: Stop and manual Reset,
b yellow trip flag indicator: overload relay tripped.
Protection by magnetic circuit breaker GV2 LE, see pages A6/11 and A6/20.SKU: Overload7
There are no reviews yet.