Two gang two way switch in curved white the ultimate in contemporary switch design. This product must be installed in accordance with local Building Regulations. If in any doubt, or where required by the law, consult a competent person who is registered with an electrical self certification scheme. Further information is available online or from your Local Authority.
White Plastic 2G 2Way Switch
Always read instructions.
₦0.00
CompareBased on 0 reviews
Be the first to review “White Plastic 2G 2Way Switch”
-
CIRCUIT BREAKERS
TeSys Schneider Electric Overload Relays 7 – 10amps
3-pole relays with screw clamp terminals
These overload relays are designed for the protection of motors. They are
compensated and phase failure sensitive. Resetting can either be manual or
automatic.
Direct mounting: under the contactor for versions with screw clamp terminals only;
pre-wired terminals, see pages B11/28 and B11/30.
Separate mounting: using terminal block LA7 K0064 (see below).
On the front face of the overload relay:
b selection of reset mode: Manual (marked H) or Automatic (marked A),
b red pushbutton: Trip Test function,
b blue pushbutton: Stop and manual Reset,
b yellow trip flag indicator: overload relay tripped.
Protection by magnetic circuit breaker GV2 LE, see pages A6/11 and A6/20.SKU: Overload4 -
ELECTRICAL INDUSTRIAL, Electro, MOTOR STARTER
ABB Enclosed Compact Motor Starter
MSSP manual switches consist of a snap switch combined with a thermal overload device operating on the solder-ratchet principle. The switch is designed to prevent being held closed under a sustained motor overload. To reset the overload mechanism, the switch lever is moved to the OFF position. The motor can be restarted by pushing the switch lever to the ON position. Applications include compressors, fans and pumps.
SKU: 312 -
LED DRIVERS
Philips Xitanium 50W 230V LED DRIVER Philip
Eco passport – Our environmental product specifications overview
Philips cares about the environment and society at large, and strongly supports eco-design of products.Specifications
General Characteristics:
Housing – [Not Specified]
Lifetime – 50000 hr
Input Frequency – 50/60 Hz
Relative Humidity – 10 (min), 90 (max) %
IP Classification – 20
Lifetime 90% surv.@Tcaselife – 50000 hr
System Description – TD/TE [Touch&DALI/Trailing edge dimming]
Number of LEDs – xOperating Characteristics
12V output – Yes
Ripple current – 20 %
Efficiency Range – 88-90 %
Power Factor Range – 0.9
Output Power Range – 15-50 W
Power Factor (100% load) – 0.9 (min) –
Output Voltage Range – 31-62 V
Output Current Range (mA) – 300-1000
Dimming range – 100-10 %
Dimmable – Yes
Input Voltage Range (DC) – 186-250 V
Inrush Current Peak – 48 (max) A
Output Current Tolerance – -5 (min), 5 (max) %
Inrush Current Width to 50% – 180 us
Type of Dimming – Touch&DALI and trailing edge
Input Voltage Range (AC) – 220-240 V
Earth leakage current – 0.7 (max) mA
Max drivers on MCB(16A type-B) – 12 (max) x
Control input protection – Yes (Basic insulation)Wiring Characteristics
Connection on driver to L2 – JST connector
Hot wiring – Yes
Connector type input terminal – Wago 250
Connector type output terminal – Wago 250Product Dimensions
Length A1 – 140.0 mm
Width B1 – 75 mm
Height C1 – 32 mm
Fixing Hole Diameter D1 – 4.5 mm
Fixing Hole Distance Width B2 – 63.7 mm
Fixing Hole Distance Length A2 – 128.5 mmSKU: Philip Driver1
There are no reviews yet.