2 way, 2 gang light switch. For your safety, this product must be installed in accordance with local Building Regulations. If in any doubt, or where required by the law, consult a competent person who is registered with an electrical self certification scheme. Further information is available online or from your Local Authority. Double light switch 2 way. If in doubt consult a qualified electrician.
Light Switch 2 Way, 2gang
Out of stock
Always read instructions.
₦400.00
Out of stock
CompareBased on 0 reviews
Be the first to review “Light Switch 2 Way, 2gang”
-
ACCESSORIES
APC 950 VA UPS
APC Back-UPS 950VA, 230V, AVR, IEC Sockets
Battery Backup & Surge Protector for Electronics and Computers
Includes : User Manual1. Automatic Voltage Regulation (AVR): Automatically steps up low voltage and steps down high voltage to levels that are suitable for your equipment.
2. Telephone dataline surge protection: Provides protection of connected equipment from power surges traveling on telephone lines.
3. USB connection: Use your PC to access additional power protection and management features for your UPS via a USB Port.
4. LED status display: Quickly understand unit and power status with visual indicators.
5. Audible alarms: Provides notification of changing utility power and UPS power conditions
6. Battery-protected and surge-only outlets: Reserves power capacity and run time for connected equipment that require UPS battery back-up while providing surge only protection for less critical equipment
7. Safety-agency approved: Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.
8. Battery and surge protected outlets: Back up and protect your hardware and data during power outages, surges and spikes.
9. Surge only outlets: Protect secondary electronics from surges and spikes without reducing battery power used to run primary electronics during an outage.SKU: APC950 -
CIRCUIT BREAKERS
TeSys Schneider Electric Overload Relays 30 – 40amps
3-pole relays with screw clamp terminals
These overload relays are designed for the protection of motors. They are
compensated and phase failure sensitive. Resetting can either be manual or
automatic.
Direct mounting: under the contactor for versions with screw clamp terminals only;
pre-wired terminals, see pages B11/28 and B11/30.
Separate mounting: using terminal block LA7 K0064 (see below).
On the front face of the overload relay:
b selection of reset mode: Manual (marked H) or Automatic (marked A),
b red pushbutton: Trip Test function,
b blue pushbutton: Stop and manual Reset,
b yellow trip flag indicator: overload relay tripped.
Protection by magnetic circuit breaker GV2 LE, see pages A6/11 and A6/20.SKU: Overload5 -
CHANDELIER LIGHT, Electro, HOME&OFFICE LIGHTING, LIGHTING
Ceiling Light Fitting Chrome 3 Armss
-For your safety, this product must be installed in accordance with local Building Regulations. If in any doubt, or where required by law, consult a competent person who is registered with an electrical self-certification scheme. Further information is available online or from your local authority-
SKU: 206 -
ARMOURED CABLE, ELECTRICAL INDUSTRIAL
70mm x 4Core Amroured Cable (Nigerchin Cable and Wire)
70mm 4 Core Armoured Cable is a size and type of steel wire armoured cable. Primarily found in large powered networks and underneath roadways supplying mains electricity to large buildings. It can also be found within the transport industry, specifically railways powering the trains and buildings located beside the tracks. Due to the size of this cable, it is perfectly suitable for large amounts of power running through it on a daily basis, 24 hours a day.
The best solution to this issue would be to buy a length of earth cable that matches the length of the Armoured Cable. This would negate the steel wire from being used as an earth, meaning it is a safer alternative.
70mm 4 Core Armoured Cable is constructed from the following materials;
– Plain Annealed Stranded Copper for the cores
– Cross-Linked Polyethylene for the Insulation
– PVC (Polyvinyl Chloride) for the bedding and sheathing
– Steel Wire for the armour protecting the insulating layers beneath.
No. of cores / size of cable – 4
Approx overall diameter – 36.8mm
Approx weight (m) – 4.23Kg
Conductors – Plain Annealed Stranded Copper
Insulation – Cross-Linked Polyethylene
Bedding – Polyvinyl Chloride
Armour / Protection – Steel Wire
Sheath / Jacket – Polyvinyl Chloride
Colour – Black
Application – Primarily found in large powered networks as well as buried underneath roads supplying mains electricity to large buildings etc.
Voltage Rating – 600/1000VtSKU: 70mmnigerchin
There are no reviews yet.